How to Stop Text from Getting Cut Off on Subway Line Display Screens?

Nov 15, 2026

Leave a message

A scene I have seen more than once: the installer finishes mounting a row of screens above the train doors, the operator's team plays the line map for the first time, and the last station name on each end is sliced in half. Everyone looks at the screen. The screen looks fine. The panel is not broken, the cable is not loose, and nobody can quite say what went wrong

In almost every case the answer is the same. The content was made for one shape and the screen is another. A 58 Inch LCD Stretched Bar Display or a 43 Inch LCD Stretched Bar Display is very long and very thin, and a line map designed on a normal 16:9 canvas does not fit it without help. This guide walks through why text gets cut off, how to fix it on site, and how to prepare content so it never happens in the first place.

The short answer text gets cut off because the content ratio, the player output and the panel's native ratio do not match, and because nobody left a safe margin at the edges. Fix the canvas size, turn off overscan, keep important text inside a 5 percent border, and test with a grid pattern before the screen goes live.

Quick AnswerWhy Does Text Get Cut Off

The three most common causes

Wrong canvas size. The content was built at 1920x1080 or similar and then stretched or cropped to fit the bar. Stretching squashes the letters, and cropping removes the ends of the line.

Overscan or scaling in the player or board. Some media players and driver boards enlarge the picture by a few percent on purpose. On a normal TV nobody notices. On a long bar with station names right at the edge, the outer letters disappear.

No safe margin. Even with the right canvas, text placed right against the edge can be hidden by the bezel, the housing or a slight offset in the panel.

A one-minute on-site checklist

Before you blame the screen, run through this:

Does the player output resolution match the panel's native resolution?

Is overscan, zoom or "fit to screen" switched off?

Does the content canvas have the same ratio as the panel?

Is any text closer than 5 percent to an edge?

Does a test grid fill the entire visible area, with the outer lines visible?

If the grid fails, the problem is the signal chain. If the grid passes and the text is still cut, the problem is the content file.

Why Subway Line Displays Use Stretched Bar Screens

A line map is a long, narrow thing by nature. Stations sit in a row, one after another. Putting that on a 16:9 screen wastes more than half the picture on empty space. A stretched bar fits the content, so the stations can be larger and easier to read.

That is also why the format has spread so quickly in rail projects, from platform walls to the inside of the train itself.

Typical installation spots and aspect ratios

Installation spot

Typical use

Common screen format

Above train doors (inside the car)

Line map, next station, door side

Bar, roughly 1:4 to 1:10

Along the car ceiling or wall

Route and transfer information

Bar, longer ratios

Platform wall or above PSD

Line map, next train, notices

43 or 58 inch bar

Concourse beside gates

Line and exit guidance

43 inch bar

The exact ratio depends on the panel. Always take the native resolution from the datasheet instead of guessing from the diagonal size.

Aspect Ratio and Resolution in Plain English

Aspect ratio is the proportion of width to height. Resolution is the number of pixels along each side. A bar panel might be something like 1920 pixels wide and a few hundred high, depending on the model. Your content must be created with exactly those numbers, or at least with the same proportion.

When the numbers do not match, the player has to do something about it. There are only three options.

Stretching, cropping and letterboxing: what each does to text

Method

What happens

Effect on text

When it is acceptable

Stretching

Picture is forced to fill the panel

Letters look wide or thin, distorted

Almost never for text

Cropping

Picture is enlarged until it fills, edges are lost

Station names at the ends are cut

Only for background images

Letterboxing

Picture keeps its ratio, empty bars appear

Text is clean but the screen is not fully used

Short-term fix

Matched canvas

Content is built at the panel's native size

Text is sharp and complete

The right way

The real fix is the last row. Everything else is a workaround.

Common Causes of Cut-Off Text and How to Fix Them

Wrong canvas size and overscan settings

Start with the player. Set its output to the panel's native resolution and switch off any scaling option. Then check the screen's own menu for overscan, zoom or aspect settings. On some boards the default is to enlarge the picture by two to five percent, which is enough to lose a letter or two at each end.

If you cannot turn it off, build a margin into the content so the lost pixels fall on empty space.

Missing safe margins

The safe margin is a border you keep clear of important content. For transit screens, 5 percent of the width on each end is a sensible minimum, and a little more is better if the housing has a deep bezel. The background can run all the way to the edge, but station names, arrows and transfer icons should stay inside the border.

This costs you a small amount of space and removes most of the problem.

Long station names and multi-language text

This is where the trouble really starts. A name that fits in English may double in length in another language, and some languages need taller characters or add accents above the line. If the design only works in one language, it will break the moment a second one is added.

Ways to handle it:

Test with the longest real station name on the line, not a short sample.

Allow two-line names where the layout permits.

Set a minimum font size and a rule for what happens when a name is too long, such as abbreviating or reducing spacing, instead of shrinking the font until it is unreadable.

Check every language together, not one after another.

Designing Content for 58 Inch and 43 Inch Stretched Bar Displays

Canvas size, safe margin and minimum font height

Use the numbers from your own panel datasheet. The table shows what to specify and the kind of values we usually work with. Replace the brackets with your actual figures.

Item

43 Inch LCD Stretched Bar Display

58 Inch LCD Stretched Bar Display

Native resolution

[confirm]

[confirm]

Aspect ratio

[confirm]

[confirm]

Canvas size for content

Same as native resolution

Same as native resolution

Safe margin (each end)

5 percent of width, minimum

5 percent of width, minimum

Safe margin (top and bottom)

5 to 8 percent of height

5 to 8 percent of height

Minimum font height

[confirm] px for 7 to 10 m viewing

[confirm] px for 10 to 15 m viewing

Output port and format

[confirm]

[confirm]

A practical rule for font height: the further away the passenger stands, the taller the characters must be. As a rough guide, character height should be about 1/250 to 1/300 of the viewing distance. At 10 metres that means around 35 to 40 mm, and you can convert that to pixels using the panel's pixel pitch. Do this calculation once, write the result into your design template, and every designer after you will follow it.

58 Inch vs 43 Inch: Which Shows More Stations Clearly

Both sizes work for line maps. The difference is how many stops you can show and how far the reader stands.

Stop capacity and best-fit installations

Item

43 Inch LCD Stretched Bar Display

58 Inch LCD Stretched Bar Display

Visible length

Shorter

Longer

Stations shown at a readable size

[e.g. 8 to 10, confirm by test]

[e.g. 12 to 15, confirm by test]

Best viewing distance

Shorter, inside the car or at gates

Longer, along platforms or wide cars

Best fit

Above doors, narrow spaces, columns

Platform walls, wide concourse walls

Risk

Names get cramped on long lines

Too large for narrow mounting spots

The station counts are only a guide. They depend on name length, font and language. We recommend mocking up your real line, with real names, on a printed strip at the right scale before you choose. It takes an hour and has saved projects a lot of rework.

If you run a long line with many stops, the better answer is often to show a section of the line at a time, with a highlight on the current station, instead of squeezing the whole route into one view.

Hardware and Software Factors That Affect Display

Driver board, bezel and pixel-to-pixel settings

Three hardware points matter more than people expect.

Driver board:it decides how the incoming signal is scaled. Ask the factory for a "pixel-to-pixel" or "1:1" mode and confirm it works with your player.

Bezel and housing:a thick bezel hides more of the picture. Check how much of the active area is actually visible after the screen is installed in its housing.

Mounting offset :a screen that sits slightly off-centre in its frame can lose a few millimetres on one side.

A good stretched bar LCD factory will supply the active area dimensions and the visible area after assembly. Ask for both.

Testing with a grid pattern before going live

Before any real content, play a grid test image at the panel's native resolution. It should have a line right at each edge, numbered squares, and a circle in the centre so you can see distortion. If every edge line is visible and the circle is round, the signal chain is correct. If not, fix the settings before you touch the content.

Do this on a screen installed in its final housing, not only on the bench. We have seen screens that passed on the table and lost the outer line once they were fitted.

Industry Trends and Standards for Transit Information Screens

Market growth and customization trend

One trend we can see directly from enquiries: operators now ask for custom sizes and ratios more than standard ones. They want the screen to match the space in the car or on the wall, instead of adjusting the space to match the screen. That makes early communication between the content team and the hardware supplier more important than before.

Legibility, CE/FCC/RoHS and rail safety requirements

Information screens in rail environments usually have to meet requirements in three areas.

Legibility: many transit authorities set minimum character heights and contrast for passenger information. Check the local requirement early.

Electrical and environmental: CE and FCC for European and American projects, RoHS for restricted substances.

Rail safety: vibration, fire and smoke requirements for use inside trains and underground stations. These differ by country and by operator, so ask for the project specification before choosing a model.

Ask the supplier for test reports, not only logos.

Real Project Mistakes and How to Avoid Them

A few patterns come up again and again.

Designing on a 16:9 template and "fitting it later." A customer once told us the line map looked perfect on the designer's monitor. It went into the train and the ends were sliced off. The designer had never seen the real ratio. The fix was a new canvas, but by then the files for the whole fleet were done. Give the content team the panel's native size on day one.

Testing with short names. The sample file used the first six stations of the line, all with short names. The long interchange stations were added later and ran off the edge. Always test with the longest names.

Trusting the bench test. A screen that looks right on the table can lose a few pixels once the bezel and housing are in place. Test in the final assembly.

Leaving overscan on. It is a default on many players and boards, and the result looks like a content problem. Check it first, it takes thirty seconds.

Shrinking the font to make everything fit. It works on the designer's screen and fails at 10 metres. Decide the minimum font height first and design around it.

How to Choose a Reliable Stretched Bar Display Manufacturer

A good stretched bar display manufacturer helps you avoid these problems before they happen. Ask

What is the native resolution and active area, and can you share a drawing

Does the driver board support pixel-to-pixel output, and can overscan be turned off

Can you customize size, ratio and resolution for our mounting space

Can we get a sample to test with our own content and player

What are the MOQ and lead time for wholesale bar type LCD display orders

On the last point, standard models usually need [confirm] pieces and [confirm] weeks, while custom ratios take longer and may need a higher quantity. Get the figures in writing and check them against your project schedule.

Also look at how the factory tests. Incoming panel inspection, burn-in and a final check of every unit are good signs. A factory that checks the visible area on each assembled screen is even better.

Get a Quote and Free Sample Advice for Your Project

If you are planning a line display project, send us what you have:the installation position and the size of the space, a draft of the line map (even a rough one), the longest station name on the line, the languages you need, and the quantity. We will suggest a screen size and ratio, tell you what safe margin and font height to design to, and, where it makes sense, arrange a sample so you can test your own content before ordering.

Our factory also takes custom stretched bar display requests, including special ratios, resolutions and housings. If the standard sizes do not fit your car or wall, tell us the dimensions and we will see what can be done

Contact now

FAQ

Q: Why is text cut off on my stretched bar display?

A: Usually the content ratio does not match the panel, overscan is switched on, or there is no safe margin. Check the player output, turn off scaling, and keep important text at least 5 percent away from every edge. A grid test image will show which of the three it is.

Q: What resolution suits a 58 inch or 43 inch stretched bar display?

A: Use the panel's native resolution, which comes from the datasheet and differs by model. Build your content at exactly that size. Choosing a standard resolution such as 1920x1080 and letting the player scale it is the most common reason for distorted or cropped text.

Q: What is a safe margin for subway display content?

A: Keep 5 percent of the width clear at each end as a minimum, and 5 to 8 percent at the top and bottom. Use more if the housing has a deep bezel. Backgrounds can run to the edge, but station names and icons should stay inside the border.

Q: Can I show 16:9 video on a stretched bar screen?

A: Technically yes, but it will be stretched, cropped or shown with empty bars. None of these suits text. If you must use 16:9 material, place it in a section of a bar-ratio layout and keep the text elements separate and sized for the bar.

Q: How do I fix overscan on a bar type LCD?

A: Open the screen's menu or the player settings and turn off overscan, zoom or "fit to screen," then set the output to the native resolution. If the board has a pixel-to-pixel mode, use it. Check the result with a grid image that has lines at the very edge.

Q: What is the minimum font size passengers can read comfortably?

A: It depends on viewing distance. As a rough guide, character height should be about 1/250 to 1/300 of the distance, so around 35 to 40 mm at 10 metres. Convert that to pixels using the panel's pixel pitch, and confirm with a printed mock-up at the right scale.

Q: Can the size and ratio be customized?

A: Usually yes, within what panels and housings are available. A factory can often adjust the dimensions, ratio, resolution and interfaces. Send your mounting space and content layout early, because custom work changes lead time and minimum order quantity.

Q: What is the usual MOQ and lead time from a factory?

A: Standard models generally have a lower MOQ and shorter lead time, and custom sizes need more of both. Exact numbers vary by supplier and order, so ask for them in writing: [confirm your MOQ] pieces and [confirm your lead time] weeks are the figures to quote.

Send Inquiry
YOUR NEEDS,WE MEET
Shenzhen Kemlink Technology Co., Ltd
contact us